Videovox Pro LNS series Manual do Utilizador

Speed Dome User’s Manual

101.2.18 Idle Status When there is no available order, you can use menu to set dome idle status after specified duration. The idle status includes tu

112 Dome Function Setup There are two ways to implement dome setup: z Keyboard or Matrix z On screen display menu If you are using keyboards or m

122.3.3 Aperture Control Aperture control is to control image light. Click OPEN or CLOSE key to modify. Aperture will go back to auto mode after in

133 Protocol、Baud Rate、Address setup 3.1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome: z Prot

145 6 Baud Rate OFF OFF 9600bps ON OFF 4800bps OFF ON 2400bps ON ON 1200bps Figure 3 Baud Rate sheet 7 8 Parity OFF OFF NONE ON OFF EVEN OFF ON OD

154 Cable Connection 4.1 RS485 and Power Cable Connection There are three cable groups here: power cable, RS 485 and Video cable. Draw out the cabl

16This series speed dome support two alarm input types: normal open/normal close. You can refer to 5.4.4 for the setup. Please follow the procedures

174.2.1 System Layout 4.2.1.1 General connection Figure 10 General connection-1 Figure 11 General connection-2 4.2.1.2 Star connection Figure 12

4.2.2 4.2.3 YwSpeecontaprotosigna2 Alarm C3 KeyboarYou can uswork simulted dome pact us if soocol. The mal and add onnectionrd Connecse a keyboaneous

195 Installation 5.1 Surface Dome Installation Step 1 —— Draw a location hole Bring the bracket-anchor out from the package. Draw four holes in

2Table of contents 1 FEATURES AND FUNCTIONS ... 8 1.1 Features .

20 Step 5 ——Take out pads Take out the two protect pads. Note: Be careful. P

21Step 8 ——Pass cable through the bracket hole. Fix bracket and loosen M4*4 bolts. Pass the cable out through the bracket hole in G1 ½ screw ho

22Step 11 ——Cable connection Please refer to chapter three cable connection. Step 12 ——Tear off transparent cover. Remove protection coating from t

23 Step 3－Cable connection Step 4－Mount the dome to the ceiling Step 5－Install transparent dome 5.3 Pendan

Step Step Step 2 —— Mak3 —— Loo4 —— Rem ke holes andsen bolts o move the low

25Step 5 —— Take out pads Take out two protection pads. Note: Be careful. Pay attention to the camera! Step 6 —— S

26 Note: add anaerobic adhesive in both sides of hoisting bean G1 1/1 to enhance water proof ability. (The prevent belt is not included i

27Step 11 ——cable connection Please refer to chapter three. Step 12 ——Tear off protection cover Remove the protection coating from the transparent

286 Menu 6.1 Screen Menu Index SYSTEM INFORMATION CAMERA PARAMETERS FUNCTION SETTING ALARM SETTING DEVICE CONTROL

29 Figure 16 Menu tree EXIT ALARM NO ：001 ACTION ：NONE CONTA

32.3 Lens Control ...

30ADDR ：001-HBAUD RATE ：9600 PARITY ：NONE PROTOCOL ：PELCO-P MODEL ：XX-SD60XX SOFTWARE ：1.20 FIRM

316.3.1 For DH-SD You can enter the dome menu directly. Use up and down key to view the function keys. Click confirm button to go to the submenu.

32INITIAL INFORMATIONSITE INFORMATION PRESET TITLE ：ON TEMPERATURE ：ON AZIMUTH/ELEV ：ON AUTO INFRARED ：ON FACTORY DEFAU

33DIGITAL ZOOM ：ONMANUAL FOCUS ：ON AUTO IRIS ：ON BRIGHT ：↑ BLC ：ON WB.MODE ：MANUAL R．GAIN ：↑ B．GAIN

34PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKING BACK EXIT PRESET NO ：001TITLE ：PRESET001 SETTING CALL BACK EXIT AUTO SCAN NO ： 001SET

35 Move joystick to highlight AUTO SCAN, click confirm button. z AUTO SCAN NO：Here is to set auto scan number. The value ranges from 1 to 5.You can

366.4.3.4 Auto pattern Figure 27 Auto pattern The dome supports maximum 5 patterns and for each pattern dwell t

376.4.3.5 Privacy mask (Window blank) Figure 28 Window blanking Highlight PRIVACY ZONE and click confirm but

38PARK FUNCTION ：OFF PARK TIME ：003MIN PARK ACTION ：NONE PRESET NO ：001 AUTOSCAN NO ：001 TOURING NO ：001 PA

39ALARM NO ：01ACTION ：NONE CONTACT ：N/O PRESET NO ：001 AUTOSCAN NO：001 TOURING NO ：001 RELAY OUT ：OFF RESET DELAY ：3S

45 INSTALLATION ... 19 5.1 Surface Dome In

40HEATER POWER ：AUTOFAN POWER ：AUTO STABLE FUNC ：OFF PICTURE FLIP ：OFF PELCO SELECT ： OFF CYCLE CAMERA POWER BACK EXIT6.4.5 Device Contr

417 DVR Connection and Setup Note: All the operation here is based on DH-SD protocol. For PELCO protocol users there might be slightly difference.

42 Figure 33 Pan/Tilt/Zoom setup After all the settings please click save button. In one window display mode, right click mouse (click “Fn” Button i

43In Figure 35, please click direction arrows (See Figure 36 ) to adjust PTZ position. There are totally 8 direction arrows. (There are only four dir

44Here you can activate the following functions: z Preset z Patrol(Tour) z Pattern z Aux on z Aux off z Auto scan z Auto pan z Light on

45 7.3.3 Patrol Setup (Tour setup) In Figure 38, click patrol button. The image is shown as in Figure 41. Input preset number and add this preset to

46 Figure 35, use direction arrows to select camera left limit Then please go to Figure 43 and click left limit button Repeat the above procedures

47Current device：dome RS485 address：1 ID: 0 8 Network Keyboard Operation (based on DH-SD) Note: all the operations here are based on DH-SD protocol.

488.3 Menu and Key Introduction Click ID and then input ID, system goes to current device connection dialogue box. Click MENU system pops up a di

49Speed：5 〈Zoom〉 〈Direction〉 〈Focus〉 〈Iris〉 Preset setup ＞value：1 GOTO Remove 8.4 Network Keyboard Operation Note: • “X” scope may

57.3.8 Activate Auto Scan ...

50Scan Value ：1 Scan setup ＞Left limit Versatile scan Right limit Random scan Speed Scan Value

51Pattern Value：1 Patter setup ＞ Start Rotation Stop Pattern Value：1 Pattern setup Start

529 For PELCO-P/D/P1/D1 Protocol 9.1 DVR Menu Setup In DVR menu, from system setting to PTZ control. The image is shown as below. See Figure 45. •

53Select Pan/tilt/zoom, system pops up an image. See Figure 47. Figure 47 PTZ Step is to control direction. Input value ranges from one to ei

549.1.3 Preset Setup and Operation Note: For PELCO-P1/D1 user, you can operate scan/pattern function. You can add tour number via dome menu and reca

55Figure 50Preset operation 9.2 From DVR Menu to Dome Menu In Figure 50 , input preset value 28 or 95 and click preset button. System pops up dome m

56Pelco-P/D/P1/D1 is different from DH-SD protocol. So please pay attention to the following instructions. The operations are as follows: Click GOTO

57SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT a. Set preset 92(left limit). b. Move PTZ

58PRESET ZAUTO SCAN TOURING PATTERN PRIVACY MASKING BACK EXIT AUTO SCAN NO ： 001 SET LEFT LIMIT SET RIGHT LIMIT DEFAULT SPEED ：011 RUN STOP BAC

SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN ZTOURING PATTERN PRIVACY MASK

6Welcome Thank you for purchasing our integrated speed dome system! This operating manual is designed to be a reference tool for the installation and

60SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN TOURING ZPATTERN PRIVACY MA

6110 FAQ 10.1 Daily Maintenance Please clean dome cover regularly to get vivid image. Handle the cover with care. Use water to wash. Don’t use

7Important Safeguards and Warnings 1．Electrical Safety All installation and operation should conform to local electrical safety codes. We assume no l

81 Features and Functions 1.1 Features Integrated dome system has the following features: z High resolution integrated digital processing camera.

91.2.7 Auto Touring Add addresses into a routine in a desired order and then set time and stop duration for each address. The dome will begin an auto